For 600dpi printers, clean after each roll of labels or when a 'CLEAN HEAD NOW' warning appears on the LCD. Printer Ribbons, Zebra, resin ribbon is UL Recognized and CSA Component Acceptable when used with Zebra approved labels.'>3200 Wax-Resin Ribbon, 40 mm x 450m, 1.57' x 1476', 1' Core, 6 rolls/case.

Zebra recommends the cleaning of the printhead regularly, either after roll of thermal transfer ribbon or after every roll of direct thermal labels. Only use a genuine Zebra printhead available from FeedYourZebra to ensure that your printer and part warranties remain intact and that the product performs optimally. When replacing your printhead, be sure to follow the directions supplied with the printhead. A consumable that wears over time, much like the brakes on your car, it requires proper installation and ongoing maintenance to ensure a long life of service for your printer.įeedYourZebra can help maximise the life of your Zebra printhead and ensure the highest possible print quality with this Zebra printhead cleaning kit available here. Most print problems are a direct result of improper care of the printhead. Zebra ZT410 - If youre printing using thermal transfer labels find ZT410 ribbons for your Zebra label printer. The printhead is a vital component of your printer that creates the image on the face of the media and therefore worn or damaged printheads should be replaced immediately.

> Zebra ZE500-4 Print Engine printheads.

> Zebra ZE500-6 Print Engine printheads.

If you see white spots, these indicate wear and that it is time for a new printhead. If after cleaning, the printing quality still hasn’t improved, open the printhead and look at the sensor for damage. If you’re using direct thermal labels that don’t require a ribbon, then using Genuine Zebra direct thermal labels will help ensure your printhead achieves the maximum usage before it needs replacing.Įvidently, with heavy use a printhead will eventually need replacing, however well you look after it. But before deciding to replace your printhead make sure that it has been properly cleaned. ZT410 Industrial Printer Support & Downloads Zebra Refer to ZT410 and ZT420 User Guide: Print Settings > Media Type to. For quality, we would recommend using either Zebra or ARMOR Inkanto ribbons. Performance You Can Rely On We design thermal and card printers, so we know them inside and out. To combat card counterfeiting, alteration and duplication, choose from our offering of overt, covert, or forensic security features. if it is too narrow, you risk scratching the printhead. It also isn’t cost beneficial to use cheap, poor quality ribbons as you will, in turn, be required to use more pressure and heat to get a good print which creates increased wear on the printhead. Experience high-definition images and barcodes combining Zebra’s plastic cards and our True Colors ribbons. If you’re using a ribbon that doesn’t exactly fit the printer, e.g. Additional pressure and heat will only result in increased wear of your printhead meaning that it needs replacing sooner.įinally, to extend the life of your printhead you should ensure that you are using the right ribbons. Shop our complete line of ZEBRA ZT410 and ZEBRA ZT411 RIBBONS including Wax Ribbons, Wax/Resin Ribbons, and Resin Ribbons. We would recommend using a printhead cleaning pen each time you use your printer, however you could reduce this to cleaning the printhead each time you change the roll of labels.Īnother technique to extend the life of your printhead is to ensure that you are using the right printer settings. The optimum printer settings that you should be aiming for is the lowest possible temperature and pressure to produce an acceptable printed image.

To do this, you simply take the nib of the cleaning pen and run it across the printhead, cleaning the entire area. The best way to clean your printhead is by using a printhead cleaning pen.

The first step is that you should be regularly cleaning your printhead, something that many people forget to do. However, there are steps that you can take to prolong the life of your printhead and delay having to purchase a new one. Zebra ZT410 / ZM400 Ribbon Supply Spindle Part Number, 79830M Refurbished Brand. With heavy use, buying a new printhead at some stage will be inevitable.

Zebra zt410 ribbon replacement